When a vehicle is rebuilt after a collision involving airbag deployment, the airbag computer must be replaced. Did you use this instructable in your classroom?

Add a Teacher Note to share how you incorporated it into your lesson. The airbag computer controls the supplemental restraint system in your vehicle, including the airbag sensors, inflators and seat belt pretensioners.

It also acts as a black box when you get into a major collision that involved airbag deployment. The airbag computer is located underneath the dashboard. The bottom half needs to be removed to access it. From a clean, uncrashed Corolla, I dumped the information from its SRS computer and it looks like this:. The SRS light should go out within 6 seconds if everything is functioning normally.

I think Ford uses a 47ohm resister. Plug a resistor in to every connector for each air bag and seat belt and if it is reset correctly the dash airbag light should go out and have no codes. If not reset properly and the module wants to deploy an airbag or belt the resistor will fail. Hi, Thank you for this video. Like Airbag sensor Toyota, - Question 1 year ago on Introduction. Hi Again, Have you ever disabled the immobilizer?

Im asking because I can buy a car with an with an immobilizer fault or lost keys for very cheap, and you can buy an new ECU with the immobilizer disabled, but I really like the idea of doing it myself.

Reply 2 years ago.

How to Reset The Airbag Status Light On A Nissan

I did some research and found that there are services out there that clear the info from the SRS computer. By speedkar9 Follow. More by the author:. Add Teacher Note. And your airbags deploy:. Disconnect battery before working on SRS system:. And It works! Did you make this project?Airbag Module Resetting Services. Here at AirbagReset. You will find great value tools, some of which will remove crash data from airbag modules via the 16 pin OBD socket so the airbag module does not need to be removed or sent away for resetting or repair.

Browse our Airbag Reset Tool Shop. The Airbag Help section of our website provides some useful articles and help for airbag warning light problems and airbag system faults.

How to Reset SRS Airbag Module After Crash Full Process EEPROM Removal And Reinstallation

We cannot provide individual help for your airbag light problems but we can put you in touch with local airbag technicians should you need somebody to fix your vehicle for you. Find A Local Airbag Technician. Crash data is recorded in the memory of an airbag module after an impact has been detected.

airbag reset

This data will contain information relating to the accident or airbag deployment event. In most modules this data is hard written so that it cannot be erased by normal diagnostic equipment as it may be data that is required by the vehicle repairer or for investigation purposes. The fact that the crash data is hard written is what locks the airbag module and renders it un-useable which is why the only option used to be to replace the module at hundreds of pounds.

However, with bench programming systems and software, the crash data can be removed from airbag modules restoring them to there pre-accident factory condition and allowing them to be re-used rather than buying a new module.

We offer crash data removal and airbag module resetting services for most airbag modules on the market meaning that you can simply post your original module for repair at a fraction of the cost of a new unit and re-use it when repairing your vehicle.

This service is ideal for bodyshops, vehicle repairiers and clients involved in the repair of autosalvage where budgets are tight. You may order airbag module resetting services here.We offer crash data removal from SRS airbag modules with hard codes after accident. We use original parts and data. Your airbags will function as normal and will deploy if accident occurs. All prices include return shipping for domestic customers. We ship back next business day after we receive your package.

Best airbag module reset service in the industry. After accident, seat belts locked. We repair and rebuild retractors replace ignitors restore to original OEM specs. Safety number one priority. Simply send in your defective, locked or blown seat belts and or SRS airbag module s to us, we will fix repair and send them back the next day.

Complete a checkout online and mail your items. Get yours reset and save. We remove crash data after accident restoring your original airbag module to OEM specs.

Simply send your airbag module to us we will reset within. Skip to content. Our goal is to provide quality reset and repair service. Visit shop. Get in touch.

Welcome to SRSModule. Airbag Seatbelt service. Call us today:. Our Services. OEM Parts We use original parts and data. World wide shipping All prices include return shipping for domestic customers. Select from most common items or navigate to the shop. Visit Shop. From the blog.The SRS airbag module is often referred to as the airbag computer, derm unit, airbag sensor as well as the diagnostic unit.

In most situations once the airbags have deployed you will need to either replace it with a new or a recycled airbag module. By resetting the vehicles original SRS airbag module, auto repair shops across the country count on our reset services to lower the cost of rebuilding vehicles. During the reset process we simply read and clear any airbag codes present in the air bag computer.

All other data is left intact, therefore, in most cases an additional trip to your auto dealer can be avoided. Once you have replaced the necessary SRS air bag components that activated during the accident, you can install the airbag module to clear the airbag light and the SRS system is reactivated.

If you would like to have your airbag modules reset. Select the year, make and model of your vehicle and click the "Reset Module" button to get started. Instructions on how to mail us your module will be sent to you by email. More replacement airbags than anyone in the industry. Become a member and instantly find the cost of replacing your car airbags. Is your airbag light on? Ask a representative about our airbag module repair service.

If you are going to be used airbag parts why not buy them from a reliable airbag expert. US Dollar Euro. Register Log in Wishlist 0 Shopping cart 0. You have no items in your shopping cart.

Select Model. Select Year Airbag Module Resets. An srs airbag module purchased from salvage yards often contain crash codes and are inaffective without additional intervention by a scan tool or technician. With our Module Reset process, we can reprogram your vehicles existing module, read on Customer service.If you have recently installed a new stereo or removed the seats in your Nissan, you may have noticed the airbag status light will not stop blinking.

There is a simple fix for this that will keep you from having to take it to the dealer. Follow these steps to reset the airbag status light on a Nissan Auto. Notice that the light will stay on and then start blinking. After turning the key to ON, wait until the light turns to off, to start the blinking process, and then switch the key OFF and remove the key. Wait 5 seconds and repeat step 1. This should be completed three times. The status light may have a different blinking pattern at this point.

Simply follow the same simple steps. Insert the key into the ignition and turn it to ON. Wait until the light turns off to start the blinking process and quickly turn the key to OFF and remove the key. Do this process a total of 2 more times. When you are complete, you should have inserted the key and removed it for a total of 6 times.

Now turn the key and start the car. The status light should stay lit and finally turn off as it normally should. If the light begins to blink again, repeat the steps above. This article was written by the It Still Runs team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. To submit your questions or ideas, or to simply learn more about It Still Runs, contact us. Step 1 Insert the key into the ignition and turn the key to ON.

Step 2 Notice that the light will stay on and then start blinking. Step 3 Wait 5 seconds. Stick the key back in the ignition and repeat step 1. Step 4 Wait 5 seconds and repeat step 1. About the Author This article was written by the It Still Runs team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information.We reset all fault codes, which means that after you receive your repaired module from us you will not have to take it to the dealership for additional programming.

All airbag control modules can be reset and reprogrammed, except modules that were damaged by a flood, fire, or some other kind of damage that impacted the hardware. Airbag control modules store hard and soft codes caused by accidents.

Even after small accidents, fault codes will be stored in the module which will turn on the airbag light. We reset and clear all crash codes inside the computer module which will turn off the airbag light. One of the biggest benefits of letting MyAirbags repair your airbag module is that you will not need to have the module coded to your vehicle VIN since it is original and came out of your vehicle. This will save you time and money! The SRS airbag control module must be reset if your vehicle was in an accident and the airbag light is on.

If the light is on but your vehicle was not in an accident, there are a variety of reasons why this may have happened. The highly skilled technicians at MyAirbags will be able to perform a thorough examination in order to find the problem and repair it.

airbag reset

MyAirbags is committed to helping you reset your airbag module and seat belts. We provide a reset and return service to reset airbag control modules. This service requires you to remove and send your module to us for reset. When we receive your airbag module, we reset ALL fault codes. After we return it, you will not have to take it to the dealer for programming. If your vehicle was in an accident, we recommend that you send your original module to us for reset. This will save you hundreds of dollars and will help you avoid an unnecessary trip to the dealer for re-coding.

If your vehicle has NOT been involved in an accident, but the airbag light is on, please read this article. If the airbag light in your vehicle randomly turned on, there may be an issue with the airbag system computer. There may also be connection issues between components or faulty components within the airbag system, including faulty:.

In order to fix this problem, one or more of these faulty components may need to be replaced. In this particular situation, we recommend you watch the accompanying tips and tech video and have your module scanned by a body shop technician before mailing your airbag module to us. After watching this video and having a body shop tech scan your module, you may discover that there is a fault in the airbag module. If that is the case, send the airbag module to our facility.

Our IPC-certified repair technicians will quickly restore your airbag module to its original factory settings and get you back on the road fast! Reset airbag modules eliminate the need for any additional programming, and, when properly installing the module back in your vehicle, the airbag light will turn off. The module is free from all hard and soft codes.

How to Reset an Airbag Light

If your airbag light is still on after reinstalling it back in the vehicle, there is most likely a problem with one of the connections or one of the following components are bad:. Ensure that all SRS components and connections are good.

Also, ensure that all purchased components are not taken from a flooded vehicle. In conclusion: if you still have an airbag light on after receiving your repair service from MyAirbags, and have properly followed the proper procedures for correct installation, then there are additional problems that only a body shop technician is capable of addressing.

If you were to buy a used airbag module, you may have many other problems to deal with.When working on the electrical components in your dash, you may find you will also need to reset the airbag light once it is all put back together.

Many people who try to do their own work, like putting in a car radio, will sometimes neglect to plug in all of the airbag components. This will cause the airbag light to blink. Resetting the light is an easy car repair you can DIY. Here are some easy steps to reset the airbag light. These are generic instructions and may not apply to your particular vehicle.

Consult owner's manual for instructions if provided, otherwise it will be a job for a specialist. If there are any unplugged components within the dash you will need to plug them in before attempting to reset the airbag light. Once the airbag light comes on it will stay on for a total of seven seconds. Once it turns off, you will have a second to turn the ignition back to "Off. Repeat the first few steps two more times and you will see that you have reset the airbag light on the dash.

You will know that it is reset once the light comes on and turns off. It will not flash. We welcome your comments and suggestions. All information is provided "AS IS. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use.

View our Privacy Policy here. Toggle navigation Login Register How-Tos. How to Reset an Airbag Light. Written by Tim Bossie. Reviewed by H. Step 1 - Plug in Components If there are any unplugged components within the dash you will need to plug them in before attempting to reset the airbag light.

Step 2 - Turn Ignition to "On" To start the process get your watch ready and turn the ignition switch from "Off" to "On. And that's how you reset an airbag light. If only all your DIY projects could be this easy. Step-by-step Vehicle Repairs. Popular Articles. How to Test an Airbag Cover. How to Reset an Airbag Module.

airbag reset

By Sage C. How to Test an Airbag Sensor. How to Reset an Airbag Sensor.